Search Results

The low auto-ignition temperature, rapid evaporation and high cetane number of dimethyl ether (DME) enables the use of low-pressure direct injection in compression ignition engines, thus potentially bringing the cost of the injection system down. This in turn holds the promise of bringing CI efficiency to even the smallest engines. A 50cc crankcase scavenged two-stroke CI engine was built based on moped parts. The major alterations were a new cylinder head and a 100 bar DI system using a GDI-type injector. Power is limited by carbon monoxide emission but smoke-free operation and NOx < 200ppm is achieved at all points of operation.

The increased rates of research on complex fuel blends in engine applications poses a need for more efficient and accurate fuel blending processes in engine laboratories. Making the fuel blending process automatic, effective, accurate and flexible saves time, storage space and cost without compromising the tests of future fuel alternatives. To meet these requirements, an automatic fuel blending system, following a sequential batch process, was designed and tested for engine laboratory application. The fuel blending system was evaluated in terms of functionality, safety, accuracy and repeatability. The functionality and safety was evaluated through a risk analysis. Whereas, the accuracy and repeatability of the system was investigated through blend preparation tests. The results show that the minimum fuel mass limitation of the system is 0.5 kg. This allows for blends with fuel ratios as low as 7 vol-% to be prepared by the system.

Through an addition of a small amount of hydrogen to the main fuel, combustion process can be considerably enhanced in internal combustion engines producing significantly lower levels of exhaust emissions. This improvement in combustion can be mainly attributed to the faster and cleaner burning characteristics of hydrogen in comparison to conventional liquid and gaseous fuels. An oxygen-enrichment of a fuel-air mixture also improves thermal efficiency and reduces especially particulate, carbon monoxide and unburned hydrocarbon emissions in exhaust. This contribution describes the results of experimental investigation where a small amount of hydrogen and oxygen is produced by Hydrogen Generating System through the electrical dissociation of water and are added to the intake of a compression ignition engine operating on a commercial diesel fuel. It is shown that level of exhaust emissions including NOx can be moderately reduced using such a pre-treatment method in diesel engines.

To date the market for P/M stainless steel has not developed appreciably, and has centered largely on the development of austenitic 300 series stainless steels. Although these stainless steels are noted for their resistance to corrosion in many media, it has been difficult for P/M parts fabricators to produce parts that will sustain 1,000 hours of protection in a 5% salt solution. The problem starts with the water atomized powders and continues with the sintering practice exercised to produce the parts. Reasons for lack of corrosion resistance, based upon these considerations, will be discussed. In addition, the ferritic stainless steels are being considered seriously for fuel injectors. These emerging applications derive from the corrosive environment that may become a problem if and when alternative fuels are introduced. P/M ferritic stainless steels may also assume a position as a corrosion resistant magnetic material required in ABS systems which are currently emerging.

The SAE Mini Baja® competition is an extremely popular design competition that focuses on the design of an off-road vehicle for performance and cost-of-production. A 2006-07 EPA P3 Phase I grant was awarded to the University of Alabama at Birmingham to convert a vehicle created for the SAE Mini Baja® competition to a biodiesel vehicle. Because of the major size difference in the diesel engine chosen compared to the much smaller gasoline engine, conversion of the Baja vehicle required considerably more effort than expected. While many mechanical aspects of the bio-diesel conversion were more complicated than expected, the students were successful in creating bio-diesel and in modifying important vehicle systems. The students also gained a substantial understanding of the economical and environmental aspects of alternative fuel generation. Through the conversion experience gained at UAB, the rules for a new competition were explored.

Flexibility in running with different fuel is becoming an important issue in the Internal Combustion Engine design due to the increasingly wider use of alternative fuels. The injection systems must deal with fuels having different properties and effects on engine behavior and take proper adjustments in the control strategy. Particularly the transient during which one fuel is being replaced by the second one is a critical point of the injection system operation, and its capability of recognizing the fuel mixture currently available is a fundamental matter in the engine control development. This paper focuses on the multidimensional CFD analysis of a Common Rail type multi-fuel injection system accumulator during the gasoline - ethanol shift. An open source computational fluid dynamics code was used in the modeling.

An advanced fuel injector designed specifically for low energy density gaseous fuels has been developed which demonstrates compelling performance advantages over fuel injectors utilizing conventional solenoid technology. The injector incorporates design features that are necessary to optimize the performance for fuels such as CNG, LNG, and propane. This paper provides a background of magnetic latching technology and addresses the application of the technology to an advanced, pressure balanced, gaseous fuel injector. Performance of the injector will be discussed in detail as will features of the injector specifically adapted for gaseous applications. The ability of the injector to solve fuel metering problems facing the industry, such as turn down ratio limitations, accuracy, durability, and compatibility with existing engine electronics, are addressed.

Performance of a CNG (Compressed natural gas) two stroke cycle S.I. engine using intermittent low pressure fuel injection from scavenging ports is investigated experimentally. The test engine is a two cylinder, 398 cm3, two stroke cycle spark ignition engine. Gaseous fuel injectors are attached at the engine block, and a CNG is injected into the scavenging passage through a fuel injection pipe. The fuel injection pressure is set at 0.255 MPa, and the fuel is injected intermittently during the scavenging process. The length and tip geometry of the fuel injection pipe are varied, and the effect on the engine performance is investigated. Using the scavenging port fuel injection, the BSFC is reduced by 25 %, and the lean burn limit extends from λ = 1.2 to 1.46, at the maximum. The peak of the NOx emission shifts to leaner side, and the THC emission is reduced by 47 % at the maximum.

For fuelling road transportation in the future, particularly light-duty vehicles, there has been much speculation about the use of hydrogen and fuel cells to provide electrical power to an all-electric drive train. An alternative powertrain would use a simple battery to store electricity directly, using power from the electrical grid to charge the battery when the vehicle is not in use. The energy efficiency of these two different approaches has been compared, using a complete “energy conversion chain analysis”. The successful development and introduction into the marketplace of grid-connected hybrid vehicles could eliminate the need for road vehicles to use petroleum fuels, at least for the majority of miles traveled. If electricity were to be generated primarily from sustainable primary energy sources, then road transportation would also become sustainable, resulting in an “Electricity Economy”, rather than a “Hydrogen Economy.

Life Cycle Analysis (LCA) considers the key environmental impacts for the entire life cycle of alternative products or processes in order to select the best alternative. An ideal LCA would be an expensive and time consuming process because any product or process typically involves many interacting systems and a considerable amount of data must be analysed for each system. Practical LCA methods approximate the results of an ideal analysis by setting limited analysis boundaries and by accepting some uncertainty in the data values for the systems considered. However, there is no consensus in the LCA field on the correct method of selecting boundaries or on the treatment of data set uncertainty. This paper demonstrates a new method of selecting system boundaries for LCA studies and presents a brief discussion on applying Monte Carlo Analysis to treat the uncertainty questions in LCA.

This paper reports the results of an exhaust emissions characterization from the non-catalyst control systems employed on the Mazda RX-4 rotary, the Honda CVCC, and the Chrysler electronic lean burn. Throughout the paper, exhaust emissions from these vehicles are compared to those from a Chrysler equipped with an oxidation catalyst and an air pump. The emissions characterized are carbon monoxide, hydrocarbons, nitrogen oxides, sulfur dioxide, sulfates, hydrogen sulfide, carbonyl sulfide, hydrogen cyanide, aldehydes, particulate matter, and detailed hydrocarbons. A brief description of the sampling and analysis procedures used is included within the discussion.

Increasingly challenging international engine emissions reductions have resulted in some advances in engine emissions technologies that may motivate a change from the customary ethylene glycol and/or propylene glycol bases that have been the mainstay of engine antifreeze formulations for almost a century. The new engines' components, especially exhaust gas recirculation (EGR) devices, generate much greater thermal stress on the engine coolant. The oxidation of ethylene glycol and propylene glycol may be accelerated dramatically, resulting in coolant unsuitable for continued use in as little as a few months. The industry has been working towards extended engine coolant service intervals1,2,3,4, with some recommendations for service extended to as long as five years. It follows, therefore, that a requirement for coolant change at four to six month intervals (due to accelerated oxidation & aging) would be unacceptable to vehicle owners.

The combustion of natural gas under lean premixed conditions is of current interest because it has properties that can lead to a potential decrease in pollutant formation and a high efficiency. The composition of the fuel mixture can vary depending upon its origin and can bring about significant changes in the combustion characteristics. This paper presents the experimental results of a single cylinder spark ignition engine fuelled with various natural gas compositions in lean mixture, and describes a numerical model that accounts for variations in concentrations of the fuel components. The diagnostic combustion model is based on the conventional one-zone approach. This thermodynamic analysis is coupled with a numerical resolution of energy and species conservation equations, which incorporates a detailed chemical kinetics. The numerical results demonstrate the influence of the fuel mixture composition on mass burn rates and burning velocities.

In previous papers a complete simulation model of the combustion in a gasoline rotary engine has been described. This combustion model, developed at the University of Gent and UMIST (University of Manchester Institute of Science and Technology), is based on a turbulence enhancement factor for the flame in various zones of the combustion chamber. The purpose of this paper is to give a description of the modifications of the model for a homogeneous natural gas rotary engine. The real geometry of the combustion chamber is incorporated In the model. Calculations are executed for different geometries of rotary engines (especially different positions and shapes of the recess in the rotor). Different formulas of the laminar flame speed for natural gas are examined. The turbulent flame speed is calculated with a turbulence factor or with a turbulence intensity factor. A correlation between the engine conditions and the turbulence intensity is proposed.

The paper describes the development of a reduced kinetic scheme for the evaluation of the main chemical species (particularly NO and CO) in premixed turbulent flame and its application to a quasi-dimensional combustion model for spark ignition engines. The proposed mechanism is based on the kinetic solution of three transport equations for NO, CO and H, coupled with the partial equilibrium of the so-called water-shuffle equations to derive the OH, O and H2 concentrations. The remaining species are computed applying the element conservation, while the required prompt levels were determined by a separate chemical 1D code for laminar combustion. The proposed chemical scheme was locally validated, considering a turbulent flame inside a premixed flow of air and methane, ignited by a parallel flow of hot gases, by means of a CFD simulation. Successively, it was embedded into a quasi-D thermodynamic combustion model developed by the authors for the simulation of S.I. and C.I. engines.

The paper discusses the concept, specification and overall performance of a 10 kW electric power range extender suitable for electric plug-in and series hybrid vehicles, based on a single cylinder, high speed, four stroke internal combustion engine, tested and developed at Istituto Motori CNR of Italy. This unit has been conceived from the beginning as a compact on board recharging system for the mentioned kind of means, and especially for city cars and small commercial vehicles. The paper starts by defining some characteristics, advantages and drawbacks of an electric city car, followed by the criteria adopted to characterize the nominal power of the range extender. Then, the ratio which leaded to the adoption of a single cylinder internal combustion engine is discussed, followed by an explanation of the main design characteristics of the whole unit.

This paper presents results of an assessment that identifies vehicle technology and fuel distribution system changes and costs associated with providing sufficient alternative fuels to displace one million barrels/day petroleum in the transportation sector in the 1995-2005 timeframe. The paper concludes that the capital cost of developing fuel delivery systems and a sufficient number of vehicles to achieve this displacement will be $22 billion if the alternative fuel is methanol, $36 billion if natural gas, and $288 billion if electricity. The predominant component of these costs is that of the incremental cost of the vehicles.

The 1997 Kyoto International Conference Protocol committed industrialized countries to reduce their global emissions of greenhouse gases within the period 2008 2012 by at least 5% with respect to 1990. In view of this and following the European Community directives, the Italian government approved a three-year pilot project to promote the experimental employment of biodiesel. The methyl esters of vegetable oils, known as biodiesel are receiving increasing interest because of their low environmental impact and their potential as an alternative fuel for diesel engines as they would not require any significant modification of existing engines. Consequently, an experimental research program has been developed to evaluate performance and emissions of a Diesel engine fueled with a methyl ester derived from rape seed (Rapeseed Methyl Ester or RME) by changing the composition of the diesel fuel-RME mixture. This program aims to analyze the performance and emissions of a turbocharged D.I.

A multi-hole direct injection injector was studied by means of image analysis. Methodologies based on an automatic process of cone angle measurement and edge detection were applied for the spray images generated by a 100 bar injection pressure discharged into a pressurized rigid chamber. A criterion based on pixel values was taken to localize the spray edges as angular coordinates and also with x and y position data. The high pixel values were associated with liquid phase while the low pixel values were associated to its absence. Computational codes written in MATLAB environment were used to analyze the numerical matrices associated to the images. Using the written MATLAB codes, a comparison of the effect of atmospheric back pressure, inside the chamber, on the spray pattern, cone angle and spray penetration were evaluated. The chamber was pressurized with 2.5, 5.0, 7.5 and 10 bar of back pressure. The tested fluid injected was EXXSOL D60 for simulating ethanol fuel behavior.

This paper presents the findings of a study that compared the fuel efficiency, power, emissions, engine wear and material compatability characteristics of automotive four-stroke cycle engines fueled by E95 (95 % ethyl alcohol and 5% lead free regular gasoline) and 87 pump octane number lead-free gasoline. A group of six senior Automotive Engineering Technology students, conducted the research over a one-year period. Two Mankato State University faculty served as directors for the project. The laboratory facilities at Mankato State University were used for vehicle modification and testing. Two identically equipped 1994 Geo Metros with 1.0 liter, three cylinder, throttle body fuel injected engines were used for this study. After a 6440 km (4000 mile) break-in period, to assure the cars performance characteristics were equal, one of the vehicles was converted to run on E95.